Tag Archives: NYG

SRT4 COMPLETE swap into a 1995 Neon Part 12

In part 11 of our SRT4 swap into a 1995 Neon we discussed ABS pump and mounting it into the Neon.

Here we have the SRT4 torque mount/Power steering bracket. Most Neon owners that do a SRT4 swap just use the 2.4 Stratus engine mount swap adapter and eliminate this bracket altogether. The problem with doing that, is that you cant use a upper torque mount to secure the engine in place, nor will you have power steering if you eliminate this bracket.

So, we have taken the nut that goes on the inside of the bracket, and we have measured and found that the point in which we could use our Neon passenger side mount and bolt along with this bracket.


The nut that our passenger side motor mount bolt will attach onto fits perfectly into the webbing on the backside of the SRT4 power steering/torque mount brace.




SRT4 COMPLETE swap into a 1995 Neon Part 11

In part 10 we discussed electrical wiring of our SRT4 swapped 1995 Neon.

Next up is installing the ABS pump. The engine bay in the SRT4 had a lot of room, but because we have a LOT less room in the Neon we have to modify the bracket to be able to mount the ABS pump onto the frame. The rusty piece of steel welded onto the right side of the bracket is the piece we added on.

Here, we are cutting away a lot of the ABS pump mounting bracket because all we need are the two mounting points for the ABS pump.

This is what our custom bracket looks like after a lot of cutting, and welding.



Here we have the ABS pump with our special bracket mounted to the frame.



Here we have the ABS Pump mounted, and the SRT4 brake lines are attached to the ABS pump.

SRT4 COMPLETE swap into a 1995 Neon Part 9

In our previous installment of our SRT4 swap series we showed you the differences between a lot of Neon and SRT4 components.

Now onto the fuel tank. I wanted to use the SRT4 fuel tank, SRT4 fuel pump, and SRT4 fuel lines. The tanks are very similar, except the angle of the fuel inlet, and the SRT4 straps tie down in a slightly different spot. Here we have the SRT4 fuel tank on top, and the Neon fuel tank on bottom.

Neon fuel tank on top, SRT4 fuel tank on bottom.

Because the SRT4 fuel tank is larger, the straps wouldnt tie down to the Neon.

So, we have taken some 1/4 inch steel plate, drilled it, and used these to extend out the mounting points for the fuel tank straps.


Heres the tank installed with the 1/4 inch plate along with a large spacer.



Now, the angle of the fuel filler necks are different between both cars so we eventually install a SRT4 fuel filler neck to use with the SRT4 fuel tank. This photo shows the Neon fuel filler neck and the SRT4 fuel tank. Notice the difference in angles on the inlet.

Diablosport Predator flashed the 1995 Neon NYGSRT swap today.

Today I did something that very few 1995-1999 Dodge Neon owners have ever done. I took a Diablosport Predator, connected it to my OBD2 port on my 1995 Neon and flashed a new performance program to the pcm within 3 minutes.

Now, before all of you 1995-1999 Neon owners call us and ask where you can buy this item, realize that this car is a full SRT4 swap car, and it has a SRT4 pcm, wiring harness, and obd2 port on a car that typically came with obd1 and could not be flashed.

Here are some pictures of the flashing process.

Diablosport Predator flashing 1995 Dodge Neon NYGSRT4

Diablosport Predator flashing 1995 Dodge Neon NYGSRT4

Results :
Went from 13-14 psi to 15-16 psi of boost
Boost builds up MUCH faster now
Went from 10.5:1 air fuel ratio in 4th gear to 12.0:1 air fuel ratio in 4th gear. (Car was reprogrammed to run leaner for more power with predator flash!)

Further benefit of the Predator flasher:
Can adjust idle
Can adjust when fans turn on and off
Can adjust timing
Can adjust fuel
Can adjust boost
Can adjust TONS more parameters. Its absolutely amazing.

More details here:

http://www.modernperformance.com/diablosport-predator-tuner-with-update-0305-srt4-p-1961.html

SRT4 COMPLETE swap into a 1995 Neon Part 8

In part 7 of our SRT4 swap series we discussed clutch pedal modifications that had to be made to put SRT4 clutch pedal assemblies into a Neon.

Comparison of expansion valves. The SRT4 expansion valve is on top of the strut mount. They are identical except the electrical connection is on the top instead of on the bottom (Neon).

SRT4 AC lines and dryer is installed into the Neon, as you can see the angles of the AC lines are offset further away from the strut mount.

Neon AC lines and dryer.

Rear SRT4 hubs, rotors and calipers are swapped onto the rear.

Pedal assemblies are reinstalled.

SRT4 COMPLETE swap into a 1995 Neon Part 7

Previously in our SRT4 swap series into a 1995 Neon we talked about steering column and clutch pedal placements.

Neon steering column mount on the left, SRT4 on the right.



Under the dash, some of the sheet metal needs to be cut for the pedal assemblies to fit.


In these photos you’ll see that we will be using the Neon upper mounting plate for the pedals, but we are using the SRT4 pedal assemblies. So, some work has to be done to cut, and modify the SRT4 pedal assembly and then weld the Neon upper mounting plate onto it.








Reinforcing the pedal assembly.

Heres the SRT4 pedal assembly with the Neon upper mounting plate welded onto it.

Brake booster is now attached in the engine bay and attached onto the brake pedal.

Mounting plate for the bobble strut is now cut off as we wont be needing it anymore.

SRT4 COMPLETE swap into a 1995 Neon. Part 6

Previously in our SRT swap series we started showing you the difference in clutch pedals between SRT4 and Neon.

Here we have a steel backing plate that will help reinforce the firewall and give the master cylinder a nice flat area to mount onto.

SRT4 clutch master cylinder is now in place on the firewall.

Now the backing plate is installed inside the car.

Inside the engine bay, heres the backside of the clutch master cylinder.

Why you should keep your cam gear cover on your motor

2004 SRT4 with snapped timing belt

The photo above is of a 2004 Dodge SRT4, and you may wonder why the engine is sitting at an angle.

The reason is, the customer that owns this car has a very modified engine, larger turbo, cams, and cam gears. Most owners of cars who install cam gears typically leave the cam gear covers off so that they can adjust the cam gears easily.

The problem with leaving the plastic cam gear covers off, is your timing belt and other timing accesories can be damaged. In this particular case, the customers power steering belt flew off, somehow got lodged into the timing belt assembly and destroyed the timing belt. Thankfully the 03-05 SRT4 is a non interference motor that in case the timing belt breaks the valves wont slam into the pistons, and this customer had no engine damage because of his timing belt failing.

The 2.0 Neon motor from 1995-2005 are all interference motors so if your timing belt fails, then the valves will crash into the pistons and cause catastrophic damage.

SRT4 COMPLETE swap into a 1995 Neon. Part 5

Previously in our SRT4 swap series we showed you the stock 1995 Neons 2.4 motor swap.

Teardown of the Neon dash.

Comparison of the clutch pedal assemblies. SRT4 on the left, Neon on the right. Because the SRT4 transmission is hydraulically operated, and not like the Neon transmission which is cable operated, the exact placement and location of the clutch pedal pivot is crucial. If the clutch pedal angle, or pivot point was off, it would affect the clutch engagement. So, the SRT4 factory clutch pedal assembly was used.



Here we are inside the Neon, looking at the large circular area that the brake booster attaches onto with four bolts. On the left you see a red circle that is the area we need to drill a hole for the clutch master cylinder.

SRT4 COMPLETE swap into a 1995 Neon. Part 2

Previously, in part 1 we showed you photos of the 1995 Neon that we were doing the swap onto. Now, lets show you some photos of the donor SRT4 .

Here are photos of the donor car for the swap. This is a Salvage title 2004 Dodge SRT4 with 65,000 miles. It was involved in several accidents and has had some frame damage. Because it ran well, but had a beat up exterior it made for a perfect donor car for our swap. Although it looks good in these photos, theres LOTS of bondo, and nasty repair work hiding under the paint.





Heres the business end of the donor SRT4.

The roof had cracks from the huge amounts of bondo expanding and contracting under the paint.

Interior shot.

Photos of a Mishimoto Radiator installed into a 95-99 Neon

Rich Clauser received a Mishimoto Aluminum radiator and promptly installed it into his 98 Neon with SRT4 motor swap. He sent us these photos that we decided to share with you all.

First, his stock radiator:
95-99 Neon Stock Radiator

Photos of his Mishimoto radiator installed:
Mishimoto Radiator installed into a 95-99 Neon
Mishimoto Radiator installed into a 95-99 Neon

Link to the Mishimoto Radiator on our website:

http://www.modernperformance.com/mishimoto-aluminum-radiator-9599-neon-p-1956.html

As of 9/4/09 we have ONE spot left for the incoming 95-99 Neon Quaife LSD’s

As of 9/4/09 we have ONE spot left in our 20 incoming Quaife LSD order for the 95-99 Neon.

If you’d like to get one, now that Quaife has discontinued producing these, you will need to order one with Modern Performance asap.

Read more details here:

http://blog.modernperformance.com/interested-in-getting-a-95-99-neon-quaife-limited-slip-read-this